Replacing cabin air filter

By ENIAC, originally posted on posted on mynissanleaf.com.
Even though there’s an access panel inside the glove box as well as another access panel underneath, which both pop out without tools, I feel the easiest procedure is to remove the glove box. Here’s why. First the cabin filter cover is very tight and difficult to remove and second the cabin filter removal can cause debris on the filter to fly around. The cabin filter must be squeezed (like an accordion) and folded in a bit to remove it. As you pull the filter out, the filter springs back and debris shoots off of it. If you are accessing the filter from underneath looking up behind the glove box, that debris could get in your eyes and all over your face.
With that, here’s what I did.

  • Remove the panel underneath the glove box. Pull down, no tools needed
  • Open the glove box door
  • Remove 4 phillips head screws at the top of the glove box
  • Close the glove box door
  • Remove 4 phillips head screws at the bottom of the glove box
  • Open the glove box door
  • Remove 2 phillips head screws on the inside of the glove box
  • Close the glove box door
  • Reaching underneath, pull glove box toward you. Take your time, don’t try and over power it. It’s plastic and could crack. There are connectors on the right front side of the glove box which your pulling will cause to release. They are a toolless design, similar to the panel underneath you removed.
  • Once the glove box drops a bit, remove the light assembly at the top. Don’t try to unplug the light from the connector, just simply pop the whole light assembly out from the glove box. (it’s very easy)
  • Set the glove box aside
  • Looking inside the vehicle, locate the white cabin filter cover on the left side where the glove box was
  • There’s a tab at the bottom of the cover which must be depressed to pop the cover off. If you can press the tab down with your fingers to remove it, great! However mine wouldn’t budge. If yours won’t budge, here’s what you do.
  • Slip a flat thin screwdriver into the side of the tab toward the back of the tab. Gently rock the screwdriver slightly counterclockwise four or five times. This will warm up the plastic a bit.

  • Increase the counterclockwise turn very slowly until the plastic tab clears the holder. The cover will fly off, so make sure your head isn’t in the way. I suggest this procedure because I just popped my cover off with one twist of the screwdriver and now it has a stress fracture in the plastic. Basically it’s the wrong plastic for this application and if you aren’t careful, you’ll snap that cover tab off.
  • Reach in and pinch the old filter at the top and bottom edges to get it to clear the opening
  • Grab the tab on the filter at the top and pull out and down
  • As the filter comes out you’ll need to keep squeezing the filter and pulling outward to get it to come out
  • Release your squeeze slowly to reduce the about amount of debris coming off the filter
  • To better understand this procedure, check out this YouTube video from 2:00 to 2:40. This video is for a Cube, but it works the same on the LEAF.
    • Once the filter is removed you may want to vacuum the filter cavity using your vacuum’s crevice attachment
    • To install the new filter you pinch the front edge and insert it
    • Pinching and rocking it will enable you to easily work it into place. The video also show this procedure
    • I modified my filter cover using a strand of plastic coated wire. This will allow me to pull down on the tab instead of using a screwdriver and risk damaging that tab any further

  • Attached the light in the top of the glove box
  • Line up the glove box to snap in the connectors on the right. The edge of the glove may tend to want to go to the outside of the dash opening. You’ll need to work it back in place.
  • Once aligned you can press it into the connectors
  • Insert the 2 phillips head screws on the inside of the glove box. Don’t tighten all the way. You may need to a bit of aligning.
  • Close the glove box
  • Insert 4 phillips head screws at the bottom of the glove box. Don’t tighten all the way
  • Open the glove box
  • Insert 4 phillips head screws at the top of the glove box.
  • Tighten all screws.
  • Also make sure you are not cross threading any of the screws as you tighten. If it feels way to tight as you turn, it’s cross threaded. Just back it out and start over. One of mine did that.
  • Replace the panel underneath the glove box and you’re done!

  • Some LEAF owners have used this cabin air filter http://www.amazon.com/ATP-RA-136-Carbon-Activated-Premium/dp/B005R4JF0K/

    Updated on October 12, 2018

    Was this article helpful?


    Related Articles

    Contribute to this EV Wiki: